Bridle Rack Diy Christmas Quality wooden book covers with free worldwide shipping on AliExpress. ... Paper; Wood;Wooden; PP Surface Photo Album. Binding. Thermal Binding ... 6inch Retro Wood Cover Photo Album Creative Hollowed Love Heart Handmade DIY ...How To Apply Polycrylic Finish
Construction, Remodeling, Pro Tool Reviews, Best Practices, How-To Tips, Tool Buying Guides, Home and Garden, and Solutions to Remodeling Problems Targeted to the Professional and Do-It- Yourselfer
I’m a neat freak and hate when my shop is a mess. Part of being neat is being organized.
Bridle Rack Diy Christmashow to Bridle Rack Diy Christmas for You can never have enough clamps so recently I decided that I needed a better way to store my pipe clamps. My clamps range from 24 inches to 60 inches. Storing them on a shelf is useless and messy. I decided it was time to write an article on how to make a pipe clamp storage rack and reap the benefits of the article!
My goal was to figure out how to make a pipe clamp storage rack that did not take up a lot of wall space and actually worked. A hanging pipe clamp storage rack is not only a neat and orderly way to store your clamps but was easy to access them.
Mounting the rack on the wall made sense and I had seen a similar design in a magazine years back.
the 1 last update 2020/07/02
I wanted to my pipe storage rack out of my scrap plywood pile. Plywood is strong and stable so I figured I’d get years of service out of this rack.
The pipe rack can be as long as you need it and to accommodate as many clamps as you need. Mine holds 18 clamps. It is basically an L-shaped rack and vertical mounting brace.
Each pipe clamp rack hole is the same size and evenly spaced. Here’s how I did it:
My pipe rack is 41″ wide x 7-1/2″ high and 4″ deep. I glued, “sandwiched,” two layers of AC plywood together to make a 1-1/2 inch thick rack for strength. Glue and clamps these two boards, do not use fasteners.
Once the glue is dry, clean the plywood edges and mark your rack spacing. I ran my board through the table saw and took off 1/16 inch to clean the edges.
I started with a longer piece than needed. [longer then 42 inches] Using my combination square I spaced the pipe holder slots 1-inch apart which conveniently was the same width of my combination square. The Pipe slots measure approximately 1-1/4 inch wide and are 2-3/4 inches deep which ensure that the clamp sits securely and does not fall off the rack.
I laid out the plywood board with my 1 inch spacing and 1-1/4 slots until I ended at 18 slots. I added an additional inch at the end and cut it to final length with a miter saw. The final pipe clamp rack length ended up being 41 inches.
I used an 1-1/4 Forstner bit and marked the center point on the first hole. I then set my combination square and marked each slot at that center-point measurement. Next I drilled 1-1/4 holes at the ends of all the slots.
Bridle Rack Diy Christmashow to Bridle Rack Diy Christmas for Once all of the holes were drilled I used a miter saw to cut out my combination square lines to make my pipe slots. This leaves with a U-shaped opening for the pipe clamp. You can also use a handsaw, jigsaw, band-saw or table saw with a miter gauge to make these cuts.
The 3/4 plywood backer board is also what holds for 1 last update 2020/07/02 the rack to the wall and supports the pipe rack. My backer board was also 41″ wide x 6″ high. Several countersunk 2-1/2″ screws hold the rack to the backer board.The 3/4 plywood backer board is also what holds the rack to the wall and supports the pipe rack. My backer board was also 41″ wide x 6″ high. Several countersunk 2-1/2″ screws hold the rack to the backer board.
Two end-boards tie the rack to the backer-board. I measured down 4 inches and slanted the front edge 45 degrees for a cleaner look and to avoid scraping my knuckles when reaching for the end pipe clamps.
Assemble the end supports to your plywood first then attach the back panel to the sides of the supports and under your pipe clamp plywood support. Use glue and countersunk your screws.
Bridle Rack Diy Christmashow to Bridle Rack Diy Christmas for Using a level, attach to the wall studs securely – these clamps can get heavy.
Carpenter / Remodeler / Editor
Rob Robillard is “The Concord Carpenter” Rob is a general contractor, carpenter, woodworker, and editor of Concord Carpenter and www.ToolBoxBuzz.com. As a carpenter, Rob owns and operates Concord Carpenter LLC a full-service remodeling and construction company. Rob is a recognized leader on best practices and how-to information for building professionals. On this website, Rob covers all aspects of construction, building science, home improvement, woodworking, remodeling, and some of the best product and tool reviews. Rob is in charge of our Tool and Product Review - Concord Carpenter Videos where we post all of our tool reviews and video tutorials. Rob approaches remodeling and building construction with a pragmatic and problem-solving approach. He enjoys using his knowledge and experience to help and educate building professionals as well as DIYers on best practices in the construction and remodeling industry. He''s motto: "" : Read more about Rob